Supermicro 5017P-TF Bedienungsanleitung

®SUPERSERVER 5017P-TLN4F5017P-TF SUPERUSER’S MANUAL 1.0

1-2SUPERSERVER 5017P-TLN4F/TF User's Manual1-2 Motherboard FeaturesThe SuperServer 5017P-TLN4F/TF is built around the X9SPV-LN4F/F-3610ME, a sin

1-3Chapter 1: Introduction1-3 Server Chassis FeaturesThe SC504-203B is an ATX form factor chassis designed to be used in a 1U rack-mount conguration

1-4SUPERSERVER 5017P-TLN4F/TF User's ManualFigure 1-1. Intel QM77 Chipset: System Block DiagramNote: This is a general block diagram. Please se

1-5Chapter 1: Introduction1-4 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (4

1-6SUPERSERVER 5017P-TLN4F/TF User's ManualNotes

Chapter 2: Server Installation2-1Chapter 2 Server Installation2-1 OverviewThis chapter provides a quick setup checklist to get your SuperServer 5017

2-2SUPERSERVER 5017P-TLN4F/TF User's Manual•This product is for installation only in a Restricted Access Location (dedicated equipment rooms, se

Chapter 2: Server Installation2-3Rack Mounting ConsiderationsAmbient Operating TemperatureIf installed in a closed or multi-unit rack assembly, the am

2-4SUPERSERVER 5017P-TLN4F/TF User's Manual2-4 Installing the System into a RackThis section provides information on installing the SC504 chassi

Chapter 2: Server Installation2-5Figure 2-2. Installing the Chassis into a Telco RackTelco RackThe SC504 supports Telco Rack installation. The SC504

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccur

2-6SUPERSERVER 5017P-TLN4F/TF User's ManualNotes

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThere are several LEDs on the control panel as well as others on the drive carri

SUPERSERVER 5017P-TLN4F/TF User's Manual3-2Informational LEDStatus DescriptionContinuously on and redAn overheat condition has occured. (This may

Chapter 3: System Interface3-3HDDOn the SuperServer 5017P-TLN4F/TF, this LED indicates SATA drive activity when ashing.PowerIndicates power is being

SUPERSERVER 5017P-TLN4F/TF User's Manual3-4Notes

Chapter 4: System Safety4-1Chapter 4 System Safety4-1 Electrical Safety Precautions!Basic electrical safety precautions should be followed to prote

SUPERSERVER 5017P-TLN4F/TF User's Manual4-24-2 General Safety Precautions Follow these rules to ensure general safety:•Keep the area around

Chapter 4: System Safety4-34-3 ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming

SUPERSERVER 5017P-TLN4F/TF User's Manual4-44-4 Operating Precautions Care must be taken to assure that the chassis cover is in place when the

Chapter 5: Advanced Motherboard Setup5-1Chapter 5 Advanced Motherboard SetupThis chapter covers the steps required to connect the data and power cab

iiiPrefacePrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It pro-vides information for the inst

5-2SUPERSERVER 5017P-TLN4F/TF User's Manual5-2 Connecting CablesNow that the motherboard is installed, the next step is to connect the cables to

Chapter 5: Advanced Motherboard Setup5-3Figure 5-1. Control Panel Header Pins5-3 Rear I/O PortsThe I/O ports are color coded in conformance w

5-4SUPERSERVER 5017P-TLN4F/TF User's Manual5-4 Onboard Processor and HeatsinkThe X9SPV-LN4F/F-3610ME features an embedded Intel Core i7 Mobile E

Chapter 5: Advanced Motherboard Setup5-5Insert the SO DIMM module straight down. To Remove: Use your thumbs to gently push the side clips near both en

5-6SUPERSERVER 5017P-TLN4F/TF User's ManualFigure 5-4. X9SPV-LN4F/F-3610ME Layout5-7 Motherboard DetailsNotes• " " indicates the loc

Chapter 5: Advanced Motherboard Setup5-7Jumper Description Default SettingJPB1 BMC (IPMI) Enable/Disable Pins 1-2 (Enabled)JBT1 CMOS Clear See Section

5-8SUPERSERVER 5017P-TLN4F/TF User's ManualReset ButtonThe Reset Button connection is located on pins 3 and 4 of JF1 and attaches to the reset sw

Chapter 5: Advanced Motherboard Setup5-9HDD LEDThe HDD LED connection is located on pins 13 and 14 of JF1. Attach a hard drive LED cable here to displ

5-10SUPERSERVER 5017P-TLN4F/TF User's ManualFan HeadersThere are three fan headers on the motherboard, all of which are 4-pin fans (Fan 1-Fan 8).

Chapter 5: Advanced Motherboard Setup5-11Universal Serial Bus (USB)Four Universal Serial Bus ports (USB 4/5, 8/9) are located on the I/O back-panel. A

SUPERSERVER 5017P-TLN4F/TF User's ManualivChapter 5: Advanced Serverboard SetupChapter 5 provides detailed information on the X9SPV-LN4F/F-3610M

5-12SUPERSERVER 5017P-TLN4F/TF User's ManualT-SGPIO HeadersThe SGPIO (Serial General Purpose Input/Output) headers are used to communicate with t

Chapter 5: Advanced Motherboard Setup5-13DOM Power ConnectorA power connector for SATA DOM (Disk On Module) devices is located at JSD1. Connect an app

5-14SUPERSERVER 5017P-TLN4F/TF User's Manual5-9 Jumper SettingsExplanation of JumpersTo modify the operation of the mother-board, jumpers can be

Chapter 5: Advanced Motherboard Setup5-15BMC Enable/DisableJPB1 is used to enable or disable the BMC (Baseboard Management Con-trol) chip and the onbo

5-16SUPERSERVER 5017P-TLN4F/TF User's Manual5-10 Onboard IndicatorsLAN LEDsThe Ethernet ports (located beside the VGA port) have two LEDs. On ea

Chapter 5: Advanced Motherboard Setup5-175-11 SATA and SAS PortsSATA PortPin DenitionsPin# Denition Pin Denition1 Ground 2 TXP3 T

5-18SUPERSERVER 5017P-TLN4F/TF User's Manual5-12 Installing SoftwareAfter the hardware has been installed, you should rst install the operating

Chapter 5: Advanced Motherboard Setup5-19Supero Doctor III Interface Display Screen (Health Information)SuperDoctor IIIThe SuperDoctor® III program i

5-20SUPERSERVER 5017P-TLN4F/TF User's ManualSupero Doctor III Interface Display Screen (Remote Control)Note: The SuperDoctor III program and Use

Chapter 5: Advanced Motherboard Setup5-21

NotesPrefacev

Chapter 6: Advanced Chassis Setup6-1Chapter 6 Advanced Chassis SetupThis chapter covers the steps required to install components and perform mainte-

6-2SUPERSERVER 5017P-TLN4F/TF User's ManualFigure 6-1. Front and Rear Chassis Views6-2 Control PanelThe control panel (located on the front of

Chapter 6: Advanced Chassis Setup6-36-3 Removing the Chassis CoverRemoving the Chassis Cover1. Power down the system and disconnect the power cord f

6-4SUPERSERVER 5017P-TLN4F/TF User's Manual6-4 System Fans (Optional)Up to three optional system fans may be installed in the SC504 chassis. Ins

Chapter 6: Advanced Chassis Setup6-5Installing 2.5" Hard Drives2.5" hard drives may be installed in several different congurations

6-6SUPERSERVER 5017P-TLN4F/TF User's ManualTwo 2.5" HDDs In a Double Bracket, Four HDD's Total, No Expansion CardOne 3.5" Hard Dri

Chapter 6: Advanced Chassis Setup6-7Figure 6-5. Installing the Expansion Card and Riser CardRiser Card SlotExpansion Card ClipPCI Slot CoverExpansion

6-8SUPERSERVER 5017P-TLN4F/TF User's ManualFigure 6-7. Replacing the Expansion Card Clip4. Outside of the chassis, put the expansion card and t

Chapter 6: Advanced Chassis Setup6-96-7 Power SupplyThe SC504 chassis has a 200 Watt power supply. This power supply is auto-switch-ing capable. This

6-10SUPERSERVER 5017P-TLN4F/TF User's Manual4. Remove the power supply from the chassis.5. Align the mounting thru holes on the power supply wi

viTable of ContentsChapter 1 Introduction1-1 Overview ...

Chapter 7: BIOS7-1Chapter 7 BIOS 7-1 IntroductionThis chapter describes the AMI BIOS Setup Utility for the X9SPV-F/LN4F moth-erboard. The AMI ROM BI

7-2SUPERSERVER 5017P-TLN4F/TF User's ManualHow to Start the Setup UtilityNormally, the only visible Power-On Self-Test (POST) routine is the memo

Chapter 7: BIOS7-1System Overview: The following BIOS information will be displayed:System Time/System Date Use this option to change the system time

7-4SUPERSERVER 5017P-TLN4F/TF User's Manual7-3 Advanced Setup CongurationsUse the arrow keys to select Boot Setup and hit <Enter> to acc

Chapter 7: BIOS7-1Wait For 'F1' If ErrorThis forces the system to wait until the 'F1' key is pressed if an error occurs. The optio

7-6SUPERSERVER 5017P-TLN4F/TF User's ManualActive Processor CoresSet to Enabled to use a processor's Second Core and beyond. (Please refer t

Chapter 7: BIOS7-1CPU PPM CongurationPower TechnologyThis feature determines what power-saving scheme the motherboard uses. The options are Disabled

7-8SUPERSERVER 5017P-TLN4F/TF User's ManualAdvanced Chipset ControlWARNING: Setting the wrong values in the following sections may cause the sys

Chapter 7: BIOS7-1PEG0 ASPMSet this item to control ASPM (Active State Power Management) support for PEG: Device 1 Function 0. The options are Disable

7-10SUPERSERVER 5017P-TLN4F/TF User's ManualEHCI Hand-OffThis item is for Operating Systems that do not support Enhanced Host Con-troller Interfa

viiPower Fail ... 3-2NIC1 ...

Chapter 7: BIOS7-1SLP_S4 Assertion WidthUse this feature to select a minimum assertion width of the SLP_S4 signal. The options are Disabled, 1-2 Secon

7-12SUPERSERVER 5017P-TLN4F/TF User's ManualRAID ModeThe following items are displayed when RAID Mode is selected:Serial ATA Port 0~5 Hot PlugSet

Chapter 7: BIOS7-1Maximum PayloadThis feature selects the setting for the PCIE maximum payload size. The options are Auto, 128 Bytes, and 256 Bytes,

7-14SUPERSERVER 5017P-TLN4F/TF User's ManualMaximum Read RequestThis feature selects the setting for the PCI Express maximum Read Request size. T

Chapter 7: BIOS7-1Conguration Request, permitting access to Extended Functions in an ARI device immediately below the port. The options are Disabled

7-16SUPERSERVER 5017P-TLN4F/TF User's ManualCompliance SOS (Available when supported by the hardware)When set to Enabled, this feature will force

Chapter 7: BIOS7-1Ipv6 PXE SupportThis feature enables Ipv6 boot support. If disabled, an Ipv6 PXE boot option will not be created. The options are E

7-18SUPERSERVER 5017P-TLN4F/TF User's ManualRemote Access CongurationCOM1, COM2, SOL Console RedirectionUse this feature to enable console redi

Chapter 7: BIOS7-1Flow ControlThis feature allows the user to set the ow control for Console Redirection to prevent data loss caused by

7-20SUPERSERVER 5017P-TLN4F/TF User's ManualConsole Redirection Settings (for EMS)This feature allows the user to specify how the host computer

viiiSUPERSERVER 5017P-TLN4F/TF User's Manual6-2 Control Panel ...

Chapter 7: BIOS7-1ACPI Sleep StateThis setting allows you to congure the ACPI (Advanced Conguration and Power Interface) sleep state for your system

7-22SUPERSERVER 5017P-TLN4F/TF User's ManualAdd an AttemptThe settings on this section are setup parameters to connect to a remote iSCSI device.i

Chapter 7: BIOS7-1Intel(R) 82579LM / Intel(R) 82574L Gigabit Network ConnectionNIC CongurationLink SpeedUse this feature to select the link speed to

7-24SUPERSERVER 5017P-TLN4F/TF User's ManualChange SmBIOS Event Log SettingsSmbios Event LogChange this item to enable or disable all features o

Chapter 7: BIOS7-17-5 IPMI SettingsIntelligent Platform Management Interface (IPMI) is a set of common interfaces that IT administrators can use to m

7-26SUPERSERVER 5017P-TLN4F/TF User's ManualLog EFI Status CodesThis option enables or disables the logging of Extensible Firmware Interface (EFI

Chapter 7: BIOS7-17-6 BootUse this feature to congure Boot Settings:Setup Prompt TimeoutUse this feature to enter the number of seconds to wait for s

7-28SUPERSERVER 5017P-TLN4F/TF User's Manual7-7 Security Settings• If the Administrator password is dened ONLY - this controls access

Chapter 7: BIOS7-17-8 ExitSelect the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup screen.Discard Changes and Exit Select

7-30SUPERSERVER 5017P-TLN4F/TF User's ManualRestore DefaultsTo set this feature, select Restore Defaults from the Exit menu and press <Enter&g

Chapter 1 Introduction1-1 OverviewThe SuperServer 5017P-TLN4F/TF is a mini server comprised of two main sub-systems: the SC504-203B 1U chassis and t

Appendix A: POST Error Beep CodesA-1Appendix A POST Error Beep CodesThis section lists POST (Power On Self Test) error beep codes for the AMI BIOS.

A-2SUPERSERVER 5017P-TLN4F/TF User's ManualNotes

B-1Appendix B: System SpecicationsAppendix B System SpecicationsProcessorsSingle or dual Intel® Xeon Core i7 Mobile ECC processor Note: Please

B-2SUPERSERVER 5017P-TLN4F/TF User's ManualSystem Input RequirementsAC Input Voltage: 100 - 240V AC auto-range Rated Input Current: 2.6A

B-1Appendix B: System SpecicationsNotes

B-4SUPERSERVER 5017P-TLN4F/TF User's Manual(continued from front)The products sold by Supermicro are not intended for and will not be used in lif